Standard Features
• Built-in Radio Receiver -
LM312hm
• Aluminum Alloy Chassis - All rust proof aluminum construction
with powder coat baked on enamel
• Built-in Battery Backup - 24 VDC backup power with regulated
24VDC for accessories.
• Soft Start/Stop - in open and close travel motions
• DC Operator System - High torque 24 volt Permanent Magnet
DC motor
• Continuous duty operation for all applications (even during
power failures)
• Reversible arm direction for Right or Left-Handed Operation
• Breakaway Arm - Break away mounting design for the 12
- 15 ft. X 3" tubular aluminum arm
• Control Inputs - Full service controller with eight inputs
and LED indicators for loops, card reader, radio, etc...
• Inherent Obstruction Sensing - Instant Reverse Device
(IRD) monitor senses obstructions during open and close
• Led Indicators - LED diagnostic center for easy on-site
trouble shooting
• Dual Gate Operation - Each unit configurable as master
or slave operator
• Dynamic Motor Braking - to preserve arm positioning
• Magnetic Sensors - No limit switches to fail-uses magnetic
(Hall Effect) sensors to monitor arm position
• Timer to Close - adjustable from 1-33 seconds with on/off
selection
• Automatic open of gate arm when power is lost if desired
(With 15 sec. delay selection)
• Raise gate input memory will memorize multiple vehicles-ideal
for barcode scanners & AVI.
• Ability to have arm STOP in close travel if tailgating
is sensed at close loop
• Molded Polyethylene UV stabilized cover never needs wax
or paint
• Direct drive gear reducer eliminates many parts that might
otherwise fail
• Microprocessor (RISC) based electronics with watch dog
reset timer
• State of the art MOSFET motor drive technology, NO contactors
or relays
• Maximum Run Timer for motor (MRT) with anti-tamper protection
in closing direction
• Safe 24 VDC low voltage motor and control wiring.
• Open architecture PCB with space for OVERDRIVE CPU for
future expanded options
• Transorb diodes on all inputs for protection against transient
voltage spikes
• Capable of being powered by 120 VAC, 220 VAC or Solar
power, standard
• U.L. LISTED (U.S.), C-U.L. LISTED (CANADA)
• 10 year perforation warranty on cover and chassis with
2 years on electronics and mechanism.
• Interlock with memory when connected to a slide/swing
gate operator, barrier will wait to raise until that unit reaches
its full open position. Barrier will not raise if slide/swing
gate is tampered with.
• Tail gate alarm-K1 relay can be programmed to fire when
a tail gater is sensed on the close loop.
|
| Specs
• Weight: 105 lb (Without Arm)
• Barrier Arm (Boom)
• Breakaway Design - Reusable Arm
Attaches With Nylon Nuts
• Arm Lengths:
-3" O.D. Round Extruded Aluminum
-12', 15' Available With Or Without Yellow/Black Stripes (15' Requires
Internal Counter Weight)
-4" O.D. Soft Padded Arm - Yellow Padded Sleeve (Uses 2"
O.D. Tube)
-12', 14' (Both Require Adaptor Collars)
• Arm Travel: 89 Degrees Approximately
• Raise/Lower: 2.5 Seconds Approximately
• Mechanism: Direct Drive - No
Crank Arms Or Rubber Bumpers
• Electronic Controller: Micro Controller
Based (RISC)
• Surge Protection: All Inputs Protected By Ultra Fast Transorb
Surge Arrestors
• Isolated Inputs: Opto Isolated - Open, Close, Free Exit,
Safety, Shadow, Aux Open Has Memory/Non-Memory
• Outputs: K1 Relay (Option), 24 VDC Regulated Accessory Power
(500MA)
• Terminals: One 12 Pin Removable, Three 4 Pin Removable
• Timers: Select On/Off With 1 - 33 Seconds Via DIP Switch
Selection
• Position Sensing: Magnetic Hall Effect Sensors - No Mechanical
Roller Switches
• Motor Drive Output: State Of The Art Mosfet Motor Drive
Technology
• Compatibility(Accessories): All AVI, Laser Barcode Scanners,
Radio Receivers, Card Readers, Ticket Machines, Loop Detectors,
Push Buttons, Token Machines (Note: Up To .5 Amp (500MA) 24 VDC
Backed Up Accessory Power Available to Power Above Devices.)
• Selections: Dip Selections
• Switches: Aux Input Memory/Non Memory, Timer On/Off, Auto
Raise Arm If Power Fails With 15 Sec Delay/Fail Secure - Right Hand
Operation/Left Hand Operation, Relay Pulse On OLS/Relay On Except
When On CLS
• Safety Approvals: U.L. LISTED (U.S.), C-U.L. LISTED (CANADA)
• Safety Standards: UL-325 (U.S.), CSA 22.2#247 (CANADA)
• Options: K1 Relay With Programmable Operation
• Heater: 150 Watt Heater With Automatic Thermostat (For Use
In Areas Where Temperatures Fall Below 15° F)
• Slip Clutch : Allows arm to be forced up without causing
damage. Gate will close after first car passes or set to close by
timer. Arm will automatically re-level itself.
• Cabinet: Full length rust proof aluminum tower
|
