Swing
Gate Hardware |
| |
Guide
to Hinges
|
|
 |
Gate
Depot Hinge Kit For One Gate.
• Kit consists of 2 brackets, 2 bearings, 2 hinge pins and
bolts.
• Heavy duty adjustable hinge bracket with 1" flange
mount sealed bearing.
• Bracket is made of 3/8" thick steel.
• 800 lbs per pair
• We designed & make this hinge bracket exclusively.
• This is the only flange bearing on the market that is adjustable
that we know of.
• Note: the hinge is designed to move like
a shoulder joint, around in a circle and off at angles. The hinge
is easily straightened if necessary. |
$145.00 |
 |
CI3000
Heavy Swing Gate Hinges.
• Designed for both round and square gate post applications.
• Sold in pairs.
• Weight capacity: 2000 lbs per pair
• Industry's only fully machined hinge
• Maintenance free sealed bearings
• Each hinge is designed for use with both round and square
gate post applications
• Slotted yoke allows for quick & easy on-site adjustments
2-1/2" - 3"
• Zinc Plated
• Made in the USA |
$153.75
|
 |
Block
Hinges.
• Made of cold rolled steel with a stainless steel
pin & single bearing.
• Superior quality made in U.S.A.
• Hinge model 625 - Height 4" - Hinge
Gap 1-1/4"
- 400lbs per pair
• Hinge model 626 - Height 6" - Hinge
Gap 2"
- 600lbs per pair
• Hinge model 627 - Height 8" - Hinge
Gap 2-1/2"
- 1200lbs per pair |
4"
- $64.00
6" - $90.00
8" - $119.00
|
 |
Elite
Power Hinge.
• Heavy duty, super quiet hinges manufactured with double
ball bearings.
• Pivoting on a 3/4" grounded & tempered, solid stainless
steel shaft.
• Fits on 1.5" gate frame.
• Has a 3" hinge gap.
• Sold as a pair.
• Power Hinge 1 - Steel Both Sides for steel
gates & post - 3000 lbs capacity
• Power Hinge 2 - Combo for aluminum gate
with steel post - 1000 lbs capacity
• Power Hinge 3 - Aluminum both sides for
aluminum post & gate - 1000 lbs capacity |
Power Hinge 1 - $126.00
Power Hinge 2 - $125.00
Power Hinge 3 - $124.00 |
 |
2-Piece
Stainless Steel Teardrop Hinge
• High weight load capacity.
• Can be welded on as lift-off or it can be permanently mounted.
• Priced per pair.
• V2A-080 - 600 lbs.
• V2A-100 - 750 lbs.
• V2A-150 - 900 lbs. |
V2A-080 - $41.50
V2A-100 - $59.50
V2A-150 - $103.75
|
 |
Adjustable
Barrel Hinges
• Steel Ball Bearing, Grease Fitting.
• Sold in pairs.
• 4BHJ - 4-3/8" Long, 5/8" Steel
J-Bolt, 2-3/8" hinge plate. 500 lb. per pair capacity.
• 6BHJ - 6-3/4" Long, 3/4" Steel
J-Bolt, 3-3/8" hinge plate. 900 lb. per pair capacity. |
4BHJ -$36.00
6BHJ -$52.00
|
 |
FAC
Weldable Hinges
• Weld to the top and bottom of the gate instead of the sides.
• Each hinge consists of two pieces - see Details
• FACsrl 262.40 40mm(1.57") Top hinge
with bracket
• FACsrl 267.40 40mm(1.57") Bottom hinge
with bracket
- For gates up to 770 lbs
• FACsrl 262.60 60mm (2.36")Top hinge
with bracket
• FACsrl 267.60 60mm(2.36") Bottom hinge
with bracket
- For gates up to 1760 lbs |
40mm Hinge Set $132.00
60mm Hinge Set $175.00
|
Uphill
Hinges
Eagle and Ramset
Swing Gate Operators have the Uphill Arm Option |
 |
Uphill
Hinge For One Driveway Gate.
• Manufactured by us.
• Offers sealed, replaceable, & adjustable bearings.
• Fast & accurate installations now possible.
• No longer necessary to tack, measure, cut & re-weld
repeatedly to get alignment.
• 800 lbs per pair
• GD-HG12 Right Hand Side Hinge Kit
• GD-HG13 Left Hand Side Hinge Kit |
$235.00
|
 |
Light
Duty Uphill Hinge
• Heim Type Ball Joint System with Grease Fitting.
• Self aligning
• Rating: 250 - 600 lbs, depending on gate height & width
• Sold as a set. |
$130.00
|
 |
Heavy
Duty Uphill Hinge
• Bronze Self-Lubricating Sleeve Bushing with grease fittings.
• Barrel height: 6"
• Big plate: 3"h x 10"w x 1/2" thick
• Small plate: 3"h x 6"w x 1/2" thick
• Hinge gap: 1/2"
• Shaft size 3/4"
• Rating: 2000 lbs.
• Made in the USA
• Sold in pairs. |
$195.00
|
Gate
Stops |
 |
Universal
Positive Gate Stop.
• Use these to align stop position with gate operators that
require positive stops.
• Most external gate stops are unsightly & are not adjustable.
• These stops allow critical alignment of single & bi-parting
gates & are unobtrusively located by the bottom hinge
• Made exclusively by us. |
$45.00
|
 |
Elite
APSA Positive Gate Stop.
• Aluminum positive stop
with two rubber grommets. |
$55.00
|
Gate
Locks & Lock Boxes |
 |
Papaiz
model ML-37 PO Mortise Lock Set.
• Fine lockset
for garden gates.
• Has deadbolt and spring latch with keying
on both sides
• This is the best lock we have found for
garden gates.
• Made of solid brass.
• See below
for lock box. |
$45.50
As of May
14, 2008
on backorder
Please Call
for more information
|
 |
Papaiz model
ML-75 PO Mortise Lock Set.
• Fine lockset for garden gates.
• Has deadbolt and spring latch with keying on both sides.
• This is the best lock we have found for garden gates.
• Made of solid brass.
• See below for lock box. |
$45.50
As of May
14, 2008
on backorder
Please Call
for more information
|
 |
DuraGate Lock
Box for Papaiz locks.
• These boxes are made exclusively by us.
• They are made of 1/8" thick steel & include a receiver
box for the strike plate for fast & clean installation.
• Strike Plate Receiver: 10"h x 2"w x 1"d &
1/2" lip
• Lock Receiver: 10"h x 2"w x 2"d |
$38.00
|
 |
Papaiz Key Blanks
• For cutting duplicate keys for your Papaiz Lock. |
$2.50
|
 |
KwikSet Double
Cylinder Deadlatch Knob
• Hard to find KEYED ON BOTH SIDES!
• Great for garden gates.
• Backset 2-3/8" or 2-3/4".
• Kwikset KW701HX3 - Bright Brass
• Kwikset KW701HX5 - Antique
• Kwikset KW701HX26D - Satin Chrome
• Kwikset KW701HX11P - Venetian Bronze |
Brass - $49.00
Antique - $51.00
Chrome - $52.00
Bronze - $59.00
|
 |
Gravity
Gate Latch
Small:
• 1-3/4"h x 7/8"w, Weld On, Plain Steel Finish
• 1-7/8"h x 1-3/8"w, Screw On, Plain Steel Finish
• 1-7/8"h x 1-3/8"w, Screw On, Plated Finish
Large:
• 4"h x 2-1/4"w, Screw On, Painted Black Finish
bolt/throw 8" x 7/16" |
Small - $4.95
Large - $14.95
|
 |
 |
Mechanical
Cane Bolt Weld-on Style.
• Used to hold one half of a double gate closed.
• Rod extends 6-1/2" when lowered.
• 1/2" Model cane bolt or 3/4" Model cane bolt |
1/2" - $19.00
3/4" - $27.00
|
 |
Steel
Lock Boxes
• Heavy duty 13 Gauge
• 2-3/8" backset
• 2-1/8" hole
• 1-1/2" wide |
Single Hole - $14.50
Double Hole - $16.50 |
 |
Trine
Electric Release Lock.
• To be used in conjunction with dead latch locks.
• Unlocks when energized.
• TR005
- 8-16VAC/4-6VDC Use with 1/2" throw lock.
• TRS005
- 8-16VAC/4-6VDC Use with 5/8" throw lock.
• TRS00524
- 24VAC Use with 5/8" throw lock.
Trine 24 Volt Reverse Action Electric Release.
• To be used in conjunction with
dead latch locks.
• Locks when energized.
• TRS005RS
- 24VAC Use with 5/8" throw lock. |
TR005 - $55.00
TRS005 -$65.00
TRS00524 -$69.95
TRS005RS -$89.95
|
 |
Trine
Electric Release Lock Box.
• 3-5/8"h x 1-9/16"w x 5-1/8"d
• Use with the Trine Electric Release Locks. |
$12.95
|
Miscellaneous
Hardware |
 |
Overhead Gate
Hardware Kits. Allows gates to be used like conventional
garage doors.
| Description |
Gate Ht |
Gate Wt |
Spring Size |
Short |
6'6"-7'0" |
350 lbs. |
3"diam |
Regular |
7'0"-8'6" |
350 lbs. |
3"diam |
Jumbo |
7'0"-8'6" |
350 lbs. |
4"diam |
Heavy Duty Jumbo |
7'0"-8'6 |
550 lbs. |
5"diam |
Super Jumbo |
8'6"-10'6" |
350 lbs. |
4"diam |
Heavy Super Jumbo |
8'6"-10'6" |
550 lbs. |
5"diam |
3" Replacement Wheel Assembly with bracket
|
Short - $684.00
Regular - $684.00
Jumbo - $853.00
HD Jumbo - $1333.00
Super Jumbo - $1514.00
Heavy Super Jumbo - Call
Wheel Assembly - $79.00 |
 |
Stainless
Steel Armored Door Loop
• Used to connect magnetic locks from post to gate or jamb
to door
• Can also be used for key switches and other devices.
• 18 inches in length.
• 3/8 Inch
Diameter or 1/2 Inch Diameter |
3/8" -
$19.95
1/2" - $22.95
|
| |
Click
Here To See Slide Gate Hardware |
|
 |
|
|
|
