Slide Gate Hardware
Gate Depot has a Wide Variety of Slide Gate Hardware including chain, chain tensioner bolts, idler assemblies, guide rollers, gate catchers, mooring points, v-track, v-track stops, v-groove wheels, wheel boxes, mounting plates, pipe track wheels, nylon cantilever rollers, cantilever track, and carriage assemblies. We carry products from Duragate, Comunello, Liftmaster, Doorking, All-O-Matic, Eagle, Platinum Access Systems, Ramset, Linear, Security Brands, FAAC, Torxun, Modesto, Nice HySecurity, and Viking Access. If you are looking for gate locks, you will want to go back one page and click on the gate locks category. All of our sliding gate hardware is designed specifically for vehicular traffic, for pedestrian or garden gates the only option we have is barn door and overhead gate hardware which can also be found back one page in the Overhead/Barn Door Hardware category.
The Most Common Way to setup a slide gate is with a v-track and v-groove wheels, you can take a look at our Slide Gate Diagram. At the base of the support posts you will pour a concrete foundation twice as wide as the gate. Onto this concrete foundation you will mount a v-track for the gate to roll on. The gate itself will have wheelboxes welded or bolted to the bottom of it so that you can mount v-groove wheels on the bottom. Two wheels is sufficient for gates up to about 20' long. The support post nearest the operator will have a set of guide rollers attached to it that keeps the gate upright while allowing it to glide freely back and forth. The support post on the far side of the driveway will have a gate catch or mooring point installed that keeps the gate secure when it is fully closed. The rear of the gate will have extension arms welded or bolted to the top and bottom of the gate to allow the top to stay within the guide rollers and the bottom to have chain routed to the rear of the gate operator. The chain will be attached to the gate with a set of chain brackets and tensioner bolts. At the rear of the track you will install a slide gate stop to prevent the gate from running off of the track if a limit switch fails.
Cantilever Hardware is Typically Used For Chainlink Gates or in snowy areas where a gate running on a track may be obstructed. A chainlink gate will have a rolling gate wheel placed at the front to provide support when in the closed position, with a set of 4 pipe track wheels at the back end of the gate to keep the gate in line and provide support when in the open position. If you are building a heavier custom steel gate you will want to look at the Communelo Cantilever Gate Hardware distributed through Architectural Iron Design under the brand name Duragates. This system uses a "C" shaped cantilever track welded to the bottom of your gate with a set of 2 carriages that support the full weight of the gate when it is full extended in either direction. At the top of the gate you have a set of guide rollers holding the gate vertical in a similar fashion as a v-track style gate. They also sell a variety of catchers and support cups for either end of the gate. Because of the wide variety of weight and length possibilities on a custom gate it is important to properly engineer the foundation and the gate itself to support the final weight. Make sure to speak to an engineer.
If you have Specific Questions on any of our products give us a call at (888) 818-4283.
Featured Products
-
DuraGate SGK-FLAT Slide Gate Hardware Kit 1-1/2" Wide (40mm) Flat Top Gates
GD# DGT-sgk-flat MFR# SGK-FLAT• Bolt-On Hardware Kit
• Includes All Hardware to Convert to a Slide Gate
• Gate Depot Exclusive
• For 1-1/2" or 40mm Frames
See More Details$212.00 -
$38.00
-
DuraGate CHAIN-BOLT-1/2 Chain Tensioner Bolt - 1/2"
GD# DGT-chain-bolt-1-2 MFR# CHAIN-BOLT-1-2$20.00 -
Duragate RGW Rolling Gate Wheel
GD# DGT-rgw MFR# RGW• Galvanized
• For Chain Link or Ornamental Iron Gates
• 6" Rubber Wheels
• 14-1/2" Wide
• 5/8" Diameter Axle
• Fits 1-5/8" - 1-7/8" Pipe O.D. or Welds to Square Tube
See More Details$112.00 -
DuraGate DGT-TRACK Slide Gate V-Track - 2.4M
GD# DGT-track MFR# TRACK• 94.5 Inches Long
• 90° Angle
• Galvanized Steel
• Holes for Anchoring to Concrete
• For Single or Dual Track Applications
See More Details$41.00 -
Duragate VGR4SL Cast Iron V-Groove Wheel - 4" Slim / 800 Lbs
GD# DGT-vgr4sl MFR# VGR4SL• 4" x 1-1/2" Wheel - Slim
• 800 Lbs Gate Weight Capacity
• Cast Iron
• Axle Dia. 1/2"
• Hub Width 2"
• Grease Fitting
• Axle, Bolt & Nut Included
See More Details$31.00 -
Duragate VGR4STD Cast Iron V-Groove Wheel - 4" / 800 Lbs
GD# DGT-vgr4std MFR# VGR4STD• 4" x 2" Wheel
• 800 Lbs Gate Weight Capacity
• Cast Iron
• Axle Dia. 1/2"
• Hub Width 2-1/2"
• Grease Fitting
• Axle, Bolt & Nut Included
See More Details$37.00 -
Duragate VGR6STD Cast Iron V-Groove Wheel - 6" / 1,000 Lbs
GD# DGT-vgr6std MFR# VGR6STD• 6" x 2" Wheel
• 1,000 Lbs Gate Weight Capacity
• Cast Iron
• Axle Dia. 1/2"
• Hub Width 2-1/2"
• Grease Fitting
• Axle, Bolt & Nut Included
See More Details$49.00 -
DuraGate DGT-WHEEL-V4 Hardened Steel V-Groove Wheel - 4" / 3,000 Lbs
GD# DGT-wheel-v4 MFR# WHEEL-V4• 4" Wheel
• 3,000 Lbs Gate Weight Capacity
• Hardened Steel w / Gold Zinc Coating
• 2" Hub Width
• Axle Bolt & Nut Included
See More Details$44.00 -
Duragate PTW Pipe Track Wheel - 5" Light Duty
GD# DGT-ptw MFR# PTW• Galvanized & Riveted Together
• For 1-5/8" o.d. pipe
• 5/8" dia x 5" bolt
• Bracket included
See More Details$35.00 -
DuraGate GR6KT Single Guide Roller - 6" Rubber / Black
GD# DGT-gr6kt MFR# GR6KT• 6" x 2-3/8"
• Black
• Rubber
• 1/2" Axle Bolt
• 2-7/8" Offset
• Includes Locknuts & Weldable Mounting Bracket
See More Details$21.00 -
Liftmaster AUHM Single Guide Roller - 6" UHMW / Black
GD# LFM-auhm MFR# AUHM• 6" Black UHMW Single Guide Roller
See More Details$70.00 -
Ramset 800-83-50 Adjustable Guide Roller Assembly - 6" UHMW / Black
GD# RAM-800-83-50 MFR# 800-83-50$105.00 -
DuraGate DGT-CATCHER-50mm Slide Gate Catcher - 2" Gates / Nylon Liner
GD# DGT-catcher-50mm MFR# CATCHER-50MM$26.00 -
$13.00
-
Doorking 2600-818 Chain Idler Assembly
GD# DKS-2600-818 MFR# 2600-818• Use with rear-mount slide gate operators
• Works with #40 and #41 chain
• All Products Require a 3-5 Day Lead Time
See More Details$111.00 -
DoorKing 2600-479 Master Link - #35
GD# DKS-2600-479 MFR# 2600-479$6.90 -
DuraGate VGRBOX Steel Wheel Boxes
GD# DGT-vgr-box-bundleFrom $12.00 To $23.00 -
Liftmaster GR123-RB Single Guide Roller - 11" Neoprene / Black
GD# LFM-gr123-rb MFR# GR123-RB• 11" Black Neoprene Single Guide Roller
• 5/8" zinc-plated bolt and nut
• Silent operation
• Steel roller bearings
• Steel-reinforced roller
See More Details$254.00 -
DuraGate CATCHER-40mm Slide Gate Catcher - 1-1/2" Gates / Nylon Liner
GD# DGT-CATCHER-40mm MFR# CATCHER-40MM$22.00 -
Comunello 253-40 Nylon Side Roller - 10"
GD# COM-253-40 MFR# 253-40• Nylon Support Roller - 10"
• Alternative to top guide
• There is a 20% Restock Fee on all products
See More Details$88.00 -
Comunello 255-220-C Adjustable Guiding Plate - 2-3/8" Frame
GD# COM-255-220-c MFR# 255-220-C• For frames up to 2-3/8"
• Top guide assembly
• 4 covered 1-1/4" rollers
• There is a 20% Restock Fee on all products
See More Details$59.00 -
Comunello 256-220 Adjustable Guiding Plate -3" Frame
GD# COM-256-220 MFR# 256-220• For frames up to 3"
• Heavy duty top guide assembly
• 4 covered 1-1/4" rollers
• There is a 20% Restock Fee on all products
See More Details$94.00 -
Comunello CG-254 U-Channel Guide - Galvanized Steel / 9' 10"
GD# COM-cg-254 MFR# CG-254• 1-1/2" x 9' 10"
• Steel U-channel
• For side mounted guide rollers
• For arched or decoratively topped gates
• There is a 20% Restock Fee on all products
See More Details$208.00 -
Comunello 256-300 Adjustable Guiding Plate - 4-1/2" Frame
GD# COM-256-300 MFR# 256-300• For frames up to 4-1/2"
• Heavy duty top guide assembly
• 4 covered 1-1/2" rollers
• There is a 20% Restock Fee on all products
See More Details$126.00 -
Comunello 293-10FT V-Track - Bolt-On - 2-1/8" x 9' 10"
GD# COM-293-10ft MFR# 293-10FT• V-Track - Bolt-On - 2-1/8" x 9' 10"
• Galvanized
• There is a 20% Restock Fee on all products
See More Details$100.00 -
Comunello 293-20FT V-Track - Bolt-On - 2-1/8" x 19' 8"
GD# COM-293-20ft MFR# 293-20FT• V-Track - Bolt-On - 2-1/8" x 19' 8"
• Galvanized
• There is a 20% Restock Fee on all products
See More Details$154.00 -
Comunello 295 Connection Pin - Bolt-On V-Track
GD# COM-295 MFR# 295• V-Track Connection Pin
• Galvanized
• For 293
• There is a 20% Restock Fee on all products
See More Details$3.50 -
Comunello Integrator CG-58-FAAC844ER Integrator Automation Adapter - FAAC 844ER / Small & Large Models
GD# COM-cg-58-faac844er MFR# CG-58-FAAC844ER• Integrator Automation Adapter - FAAC 844ER / Small & Large Models
• There is a 20% Restock Fee on all products
See More Details$258.00 -
Comunello Integrator CG-58G-FAAC844 Integrator Automation Adapter - FAAC 844ER / Grande Model
GD# COM-cg-58g-faac844 MFR# CG-58G-FAAC844• Integrator Automation Adapter - FAAC 844ER / Grande Model
• There is a 20% Restock Fee on all products
See More Details$258.00 -
Comunello Duragates CGS-150.5M Mini Multiplate Carriage - Galvanized / 660 Lbs
GD# COM-cgs-150.5m MFR# CGS-150.5M• 8' x 660 Lbs / 13' x 330 Lbs
• Mini Multiplate Carriage Body
• 5 Wheel Carriage
• 2-3/4" x 2-3/4" x 9' 10" Galvanized Track
• There is a 20% Restock Fee on all products
See More Details$218.00 -
Comunello CGS-245M-6.6FT Cantilever Track - Galvanized Steel / 2-3/4" x 6' 6"
GD# COM-cgs-245m-6.6ft MFR# CGS-245M-6.6FT• 2-3/4" x 2-3/4" x 6' 6"
• Galvanized Steel Track
• Bottom Track For CGS-250.8M & CGS-150.5M Carriages
• There is a 20% Restock Fee on all products
See More Details$136.00 -
Comunello CGS-345P-6.6FT Cantilever Track - Galvanized Steel / 3-1/2" x 6' 6"
GD# COM-cgs-345p-6.6ft MFR# CGS-345P-6.6FT• 4" x 3-1/2" x 6' 6"
• Galvanized Steel Track
• Bottom Track For CGS-350.8P & CGS-500.8P Carriages
• There is a 20% Restock Fee on all products
See More Details$210.00